Mon–Sat: 9:00 AM – 7:00 PM India
+91 9958971235 | Follow:
CretePro

— Blogs

FILA DETERDEK PRO: How to Remove Grout Haze and Cement Residue After Tiling

FILA DETERDEK PRO: How to Remove Grout Haze and Cement Residue After Tiling

A newly tiled floor often looks dull and patchy even after a careful wipe-down. The cause is a thin film of cement and grout residue left on the tile surface during installation. If it is not removed properly, it traps dirt, makes everyday cleaning harder and spoils the finish of expensive porcelain or terracotta. FILA DETERDEK PRO is a professional end-of-installation cleaner made to remove this residue in one step.

What Is FILA DETERDEK PRO?

DETERDEK PRO is a buffered acid detergent from FILA, the Italian surface care specialist. “Buffered” means its acidity is controlled, so it dissolves cement-based residue without being as harsh as raw acids such as hydrochloric acid, which are still commonly used on Indian sites.

It removes:

  • Cement and grout haze after tiling, including polymer-modified grouts
  • Limescale and hard-water deposits
  • Efflorescence (white salt bloom)
  • Rust marks and engobe residue

Its ingredients are up to 98% biodegradable, it is free of phosphates and EDTA, and it does not give off harmful fumes or damage steel or aluminium trims.

Which Surfaces Is It Suitable For?

DETERDEK PRO is designed for acid-resistant materials:

  • Porcelain and vitrified tiles
  • Glazed ceramic tiles
  • Terracotta and quarry tiles
  • Other acid-resistant stone and clinker

Do not use it on polished marble, limestone, travertine or other acid-sensitive materials. Acid etches calcareous stone and dulls its polish. For marble and other sensitive stone, use a neutral or alkaline cleaner, and always test on a small, hidden area first.

Why Not Use Ordinary Acid?

Many sites still use diluted hydrochloric acid to clean new tiles. It works on cement, but it releases harsh fumes, corrodes metal fittings and trims, and can attack grout joints. DETERDEK PRO is formulated to clean effectively while staying safer for applicators, grout and fixtures.

Dilution Guide

  • Post-installation cleaning: 1:5 to 1:10 in water, depending on how much residue there is
  • Maintenance of aged outdoor surfaces: 1:10
  • Fresh limescale, rust or engobe: undiluted

How to Use DETERDEK PRO

  1. Wait for the grout to cure. Follow the grout manufacturer’s recommended curing time before cleaning.
  2. Pre-wet the surface. Wet the tiles and joints with clean water so the grout absorbs less of the solution.
  3. Apply the solution. Spread the diluted product over a few square metres at a time.
  4. Allow a short dwell. Leave it for a few minutes. Do not let it dry on the surface.
  5. Scrub. Use a single-disc machine or an abrasive pad suited to the tile finish.
  6. Remove residue. Collect the dirty solution with a wet vacuum or microfibre cloth.
  7. Rinse thoroughly. Rinse with plenty of clean water. Repeat with a stronger solution if residue remains.

Coverage per Litre

As an indicative guide, one litre of product treats:

  • Porcelain tiles: 40 to 80 m²
  • Natural stone (acid-resistant): 20 to 35 m²
  • Terracotta: 10 to 20 m²

Where It Fits in the Tile Care Cycle

Deep cleaning after installation is the foundation for every treatment that follows. Clean, residue-free surfaces absorb protectors evenly, so once the floor is dry, protect porous materials with FILA MP90 ECO XTREME for a natural look, or FILA STONEPLUS for an enhanced tone on natural stone. For stone slabs laid on wet mortar, treating the backs with FILA PW10 before installation reduces the efflorescence you would otherwise need to clean later.

Cleaning also matters for the grout you chose. Cement-based grouts benefit most from a thorough DETERDEK PRO wash. Epoxy grouts such as MAPEI Kerapoxy should be cleaned while fresh, as described in the grout instructions.

Common Mistakes to Avoid

  • Cleaning on dry tiles: Skipping the pre-wetting step lets the grout absorb acid, which can weaken and lighten the joints.
  • Letting the solution dry: Dried residue leaves streaks and is harder to remove. Work in small sections and rinse promptly.
  • Using it too early: Cleaning before the grout has cured can wash out or discolour fresh joints.
  • Treating marble the same way as porcelain: On mixed installations with marble inlays or borders, mask the stone or clean it separately with a neutral product.
  • Skipping the rinse: Leftover detergent attracts dirt and can interfere with protectors applied afterwards.

Safety Tips

  • Wear gloves and eye protection.
  • Keep the product away from children.
  • Ventilate enclosed spaces during use.
  • Read the safety data sheet before use.

Conclusion

FILA DETERDEK PRO removes grout haze, cement residue, limescale and efflorescence from porcelain, ceramic and terracotta without the drawbacks of harsh raw acids. Used straight after installation, it reveals the true finish of your tiles and prepares them for protection. Explore FILA DETERDEK PRO at Crete Pro Trading or ask our team which FILA treatment suits your surface.

Frequently Asked Questions

1. What is FILA DETERDEK PRO used for?

FILA DETERDEK PRO is a buffered acid detergent for end-of-installation cleaning. It removes cement and grout haze, limescale, efflorescence, rust and engobe residue from porcelain, glazed ceramic, terracotta and other acid-resistant materials.

2. Can FILA DETERDEK PRO be used on marble?

No. DETERDEK PRO is acid-based and can etch and dull polished marble, limestone, travertine and other acid-sensitive stone. Use a neutral or alkaline cleaner on these materials instead.

3. What dilution should be used for FILA DETERDEK PRO?

Dilute 1:5 to 1:10 in water for post-installation cleaning, 1:10 for maintenance of aged outdoor surfaces, and use it undiluted on fresh limescale, rust or engobe.

4. How much area does one litre of DETERDEK PRO cover?

As a guide, one litre covers 40 to 80 m² of porcelain tiles, 20 to 35 m² of acid-resistant natural stone and 10 to 20 m² of terracotta, depending on dilution and residue.

5. Is FILA DETERDEK PRO safer than hydrochloric acid?

Yes. It is a buffered formula that gives off no harmful fumes, does not damage steel or aluminium trims and has up to 98% biodegradable ingredients. Gloves and eye protection are still recommended.

Need a quote for your project?

Get in touch with our team today.

+971 4577 1995