Fila Surface solution
DETERDEK PRO is a professional-grade end-of-work cleaning solution specially formulated to remove cement residues, grout haze, lime deposits, and construction dirt from newly installed surfaces. Its powerful yet controlled acidic formula effectively cleans tiles, natural stone, porcelain, and other acid-resistant materials without damaging the finish when used correctly. The product restores the original appearance of surfaces after installation, leaving them clean and ready for use. DETERDEK PRO is suitable for both indoor and outdoor applications and is widely used by contractors, installers, and maintenance professionals for post-construction cleaning.
| Product Type | Professional End-of-Work Cleaning Solution |
|---|---|
| Material Base | Acid-Based Cleaning Detergent |
| Application Method | Brush, Mop, Sponge, or Floor Cleaning Machine |
| Dilution Ratio | 1:5 to 1:10 with Water (depending on cleaning requirements) |
| Coverage | Approx. 30–50 m² per litre (depending on dilution and surface condition) |
| Contact Time | 2–5 minutes before rinsing |
| Suitable Surfaces | Porcelain, Ceramic, Terracotta, Acid-Resistant Natural Stone |
| Colour | Clear Liquid |
| Pack Size | 1 L, 5 L, and 10 L Containers |
| Storage | Store in a Cool, Dry Place Away from Direct Sunlight |
Once tiling or stone flooring is finished, most people assume the job is done. It is not, not quite yet. Every tile installation leaves behind a thin film of cement haze, grout residue, and mortar dust that a regular household cleaner will not touch. If that layer is left to dry and harden fully, it becomes far harder to remove later, sometimes requiring mechanical scrubbing that risks scratching the surface underneath. This is the exact gap Fila Deterdek Pro was built to close, and it is one reason contractors treat this step as part of the installation itself rather than an optional extra.
CretePro Trading supplies Deterdek Pro to contractors and installers across India who need this final cleaning step done right, and it is one of the products our customers ask the most questions about, mainly around timing and dilution, since getting those wrong can undo an otherwise good installation.
Timing matters more than most people expect with an end-of-work cleaner. Applying it too soon, before the grout has cured enough, can weaken the joints. Applying it too late means the cement film has hardened and needs more aggressive dilution or a longer contact time to break down.
Most contractors wait for the manufacturer’s recommended curing window before running the first clean, then test on a small, inconspicuous area first, particularly on natural stone, since acid-based cleaners can react differently depending on the stone’s mineral composition.
A second pass with clean water is just as important as the cleaning step itself. Any acidic residue left on the surface, especially on polished or honed stone, can continue reacting after the visible cleaning is done, leading to dullness or etching over time. Thorough rinsing is not optional here.
Deterdek Pro is designed for the immediate post-installation clean, not routine upkeep. Once a floor has been properly cleaned and any protective treatment applied, day-to-day maintenance should shift to a neutral pH cleaner instead, since repeated use of an acidic product on a finished surface over months or years can wear down grout lines and dull certain stone finishes. Knowing when to stop using an acid-based cleaner and switch to gentler maintenance products is as important as using it correctly in the first place.
If you are wrapping up an installation and need a reliable end-of-work cleaner, CretePro Trading can supply genuine Fila Deterdek Pro in the pack size your project needs, along with guidance on dilution and timing so the finish comes out clean the first time.
Reach out to our team for pricing and technical data sheets before your next project.
It should be used once the grout has cured enough per the installer’s or manufacturer’s recommended waiting period, since using it too early can weaken fresh joints.
It can, if not tested first or left in contact too long, so a patch test on a hidden area is recommended before treating the full surface, especially on polished or honed stone.
No, it is designed for the initial post-construction clean, not everyday maintenance, which should use a neutral pH cleaner instead.
Leftover acidic residue can keep reacting with the surface after cleaning, which may cause dullness or etching, particularly on natural stone.
It should be kept in a cool, dry place away from direct sunlight and stored in its original sealed container until you are ready to use it.
Request a quote with technical data sheet and pricing.